|
|
|
Who's Online
There currently are 6022 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual is immaculate in it's accuracy. Everything is written very clearly and easy to understand. Written by a professional who wants to convey a clear and easy to understand message!!
;
This Manual (as downloaded) is both informative and comprehensive and has proved to be extremely useful. thoroughly recommended.
;
everything is ok, thank you very much! Product is good, no problems with download!
;
Great site, I always find all the manuals I need and i can't find anywhere else. PDF for the Sony PCM 3348 is complete and scan is good quality. Thank you!
;
It was a complete manual as stated. Very good source for older product manuals. Thanks
5 How to Mow S
1. Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut. (S) 2. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection. Do Not Overload Your Mower: Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height.
Removing and Fitting the Blade and Fan T
blade bolt
Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade and Fan 1. To remove the blade bolt, hold the fan firmly and, with a 13.0mm ring spanner, loosen the blade bolt by turning it anti-clockwise (T). 2. Remove the blade bolt, blade, spacer and fan from the pulley.(T) 3. Inspect for damage and clean as necessary. Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. If the blade is cracked or damaged replace it with a new one. Fitting the Blade and Fan 1. Ensure the fan is located correctly.(T) 2. Fit the spacer to the fan. (T) 3. Fit the blade to the spacer. (T) 4 . Re-assemble blade bolt through blade, spacer and fan. 5. Hold the fan firmly and tighten blade bolt firmly with a 13.0mm ring spanner. Do not over tighten.
spacer fan
blade
pulley
Caring for your Lawmower U
Cleaning (U) � USE GLOVES � IMPORTANT: It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with a piece of wood or similar. 2. Remove the blade, see Figure T, to gain access to the fan and clean with a soft brush. 3. Raise the roller to its highest position, see Adjusting the Cutting Height, and clean with a soft brush. 4. Remove grass clippings from: all air intakes, wheels and height adjustment levers, grassbox, grassbox lid and both sides of grassbox full indicator 5. Clean around the switch actuator on the grassbox. (V) 6. Wipe over the surface of your lawnmower with a dry cloth. � IMPORTANT Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. At the End of the Mowing Season 1. Replace blade, bolts, nuts or screws, if necessary. 2. Clean your lawnmower thoroughly. 3. Ask your local Service Centre to clean the air filter thoroughly and carry out any service or repairs required. 4. Make sure that the electric cable is coiled properly. Storing the lawnmower The handles can be folded to take up the minimum of space. � Loosen the handle knobs � Fold the upper handle over the lawnmower. � Ensure the switchbox cable is not trapped. � Store in a dry place where your lawnmower is protected from damage.
V
Switch Actuator
|
|
|
> |
|
